How to seal a shower tray and bathroom joints

Shop the products for this jobShop all products →
S100Buy S100 ↗PRESCHBuy PRESCH ↗

Start where the tray meets the wall. The screen has a separate drainage path and its own fitting instructions.

Rogier · Silicrack

Seal the bathroom yourself: the order that lasts
Short answer

Check that the tray is stable. Remove the old bead, dry both edges and seal only the specified junction with a compatible product. Leave the screen outlets clear.

See tools and materials ↓

Buying through a product link may earn us a commission at no extra cost to you.

Find the joint between the tray and the wall

Dry the area and gently load the tray. If it rocks, check its support before resealing. Trace the line where the tray meets the tile. It is separate from the vertical screen frame and the concealed waste connection. If water comes from behind, find the source first.

Renew an old shower joint · Spanish audio
For this jobOTTOSEAL S100 ↗ For sanitary joints on compatible surfaces Presch silicone gun ↗ For laying a bead from a cartridge FUGENFUX ↗ For shaping the fresh bead
Check surface compatibility and the selected shade at the shop.

From the cartridge to the last corner

For a compatible sanitary joint, try PRESCH with OTTOSEAL S100 in the tightest corner before applying. Run a continuous bead and shape it with Fugenfux before a skin forms. For marble or stone, check whether OTTOSEAL S70 suits that surface. Read the product’s water-exposure time before using the shower.

Check the tray support first

A steady hand, a proper gun, a spatula and a technical cleaner: you can reseal a ceramic shower that is otherwise sound. Do not start if old silicone is still on the flanks, if the tray flexes when you stand in it, if water is already behind the tiling, or if the faces are natural stone you have never sealed. Those are strip, support, leak-path or stone-chemistry jobs first. Matt design silicone is unforgiving on tooling; practise or leave it.

New silicone on old silicone does not weld. It peels in weeks. Always recut.

If one edge is marble or natural stone, trial OTTOSEAL S70 on an offcut and check the tooling agent before touching the visible surface.

Dry-fit the FUGENFUX profiling tool. Choose the edge that meets both sides without scooping out the middle, then tool the bead before a skin forms.

Adhesion, cohesion, two faces

The bead has to stick to the tile and the tray (adhesion) and hold together in the middle (cohesion). If it also sticks to the back of the gap — three-sided adhesion — it cannot stretch. House movement then tears the mass. In a deep joint I set closed-cell PE backer rod so the silicone bonds on two flanks and works like a horizontal elastic. Skip that and a pretty face can still leak within a year.

Cheap cartridges extended with solvent can shrink as they cure and pull hollow. I use a high-solids sanitary silicone such as OTTOSEAL S100 on a normal ceramic wet room. That is a tool, not a slogan.

Before opening the cartridge, try the Presch silicone gun in the tightest corner. Check you can turn your wrist and release pressure at the end of the run.

Order of work

  1. Cut out every scrap of old bead. Use a remover on the invisible film if it remains. Degrease with a residue-free technical cleaner — not white spirit that leaves oil, not glass spray.
  2. Let the flanks dry. Primer only if that substrate needs it (plastics and some composites often do).
  3. Backer rod if the gap is deep.
  4. Cut the nozzle at about 45°, as wide as the joint, not a trumpet.
  5. Push the silicone into the joint with constant gun pressure. Laying a sausage on top traps air and fails at the edge. If you see bubbles, pull that stretch and refill before you tool.
  6. Light mist of a pH-neutral tooling liquid, not washing-up detergent and not saliva. Mouth bacteria in a wet joint is a mould starter.
  7. One clean pass with a spatula or wooden profile so water can run off. I do not love masking tape on showers: it often leaves a tiny upstand that holds soap.

Use Cleanprimer 1101 only where the manufacturer’s primer table specifies it for that sealant and non-porous substrate. Observe the flash-off time. It is not a household cleaner or stain remover.

After you finish

Skin-dry is not through-cure. Moisture-cure silicones typically build from the outside in; a figure on the order of a couple of millimetres per day at room conditions is common on packs, not a law for a cold, dry room. I keep a normal bathroom joint off a full shower for about a day, sometimes two if the section is thick. Read the cartridge you used.

Keep the room aired. Do not bleach a fresh bead to “keep it white”.

If the sealant allows a Smoothing spray, use it sparingly when tooling silicone. Keep it off the bonding faces and check for staining before using it on stone.

Tools and materials for this job

  • OTTOSEAL S100

    Sanitary silicone for compatible surfaces. Check both edges before opening the cartridge.

  • OTTOSEAL S70

    For compatible natural stone. Test colour and finish on an offcut.

  • Backer rod

    For depth control where specified. Choose the diameter to suit the measured width.

  • Cleanprimer 1101

    Pretreatment for specified non-porous substrates; consult the primer table.

  • Presch silicone gun

    Manual cartridge gun. Check you can release pressure in the last centimetre.

  • FUGENFUX

    Profiling tool. Dry-fit the edge that reaches both sides of the joint.

  • Smoothing spray

    For tooling silicone where the manufacturer allows this agent. Keep bonding faces dry.

Exceptions

Acrylic in the shower washes out; silicone on a skirting will not take paint. Stone wants stone silicone. A moving tray wants support, then a joint. If you are already leaking into the floor below, closing the visible line is not a diagnosis.

More on this

Guides · Bathroom

Seal a shower screen inside or outside? →