A gap between the skirting board and floor: should you fill it?

Shop the products for this jobShop all products →
A205Buy A205 ↗S125Buy S125 ↗

First decide whether it is a fixed trim joint or an expansion space for a floating floor. The two need different treatment.

Rogier · Silicrack

Floors and skirtings: acrylic on top, not underneath
Short answer

Under the skirting I use a neutral silicone or an elastic hybrid that takes mop water and PVC plasticisers. On top, a paintable acrylic sealant. Acrylic underneath goes soft and dirty.

See tools and materials ↓

Buying through a product link may earn us a commission at no extra cost to you.

Top and bottom edges of the skirting

A skirting on a PVC floor (or any floor you mop) does not want the same sealant top and bottom. Below there is rub, floor movement, often plasticisers from the PVC, and mop water. Above there is plaster or paint: you want a joint you can paint with the wall.

One cartridge for both lines is the usual mistake. Acrylic sealant underneath drinks water, goes soft, picks dirt and cracks. It also does not have the elasticity of a floor joint.

PVC carries plasticisers to stay flexible. Some silicones react: the bead stays tacky or discolours. Underneath I want a plasticiser-resistant neutral or an elastic hybrid. No aggressive acetic chemistry against PVC.

For a dry interior joint that will be painted, check the expected movement against the data sheet for OTTOSEAL A205. Try the finish with your actual paint.

When to seal — and when not

Yes, below: neutral silicone or elastic hybrid that takes mopping.

Yes, above: paintable elastic acrylic, to finish with the wall.

No acrylic below. First mop, water in; black edges follow.

Do not lock a floating floor that is hard against the wall. Without an expansion gap the floor humps. That is not “fixed” with paste: free the perimeter first, then an elastic bead that does not block the float.

For a compatible floor covering, consider OTTOSEAL S125 only where the floor manufacturer permits an elastic joint. Keep required expansion clearances free.

How I do it

  1. Degrease floor, skirting and wall. Factory PVC often has a film; without a clean, adhesion is weak.
  2. If the gap is deep, closed-cell PE backer rod. Without it, three-sided adhesion: floor, skirting and the wall or slab behind. The bead tears.
  3. Even bead below; tool with a suitable finisher and a spatula.
  4. Above, acrylic between skirting and wall. Tool it and let it cure before painting. Depending on temperature and humidity, from a few hours to a day; the product decides, not a universal clock.
Colour-match a PVC floor joint · Spanish audio
For this jobOTTOSEAL S125 ↗ For a compatible floor joint Presch silicone gun ↗ For laying a bead from a cartridge FUGENFUX ↗ For shaping the fresh bead
Check surface compatibility and the selected shade at the shop.
Finish a continuous floor at the wall · Spanish audio
For this jobOTTOSEAL S125 ↗ For a compatible floor joint Presch silicone gun ↗ For laying a bead from a cartridge FUGENFUX ↗ For shaping the fresh bead
Check surface compatibility and the selected shade at the shop.
Finish a door frame over PVC flooring · Spanish audio
For this jobOTTOSEAL S125 ↗ For a compatible floor joint Presch silicone gun ↗ For laying a bead from a cartridge FUGENFUX ↗ For shaping the fresh bead
Check surface compatibility and the selected shade at the shop.
Finish PVC flooring under the stairs · Spanish audio
For this jobOTTOSEAL S125 ↗ For a compatible floor joint Presch silicone gun ↗ For laying a bead from a cartridge FUGENFUX ↗ For shaping the fresh bead
Check surface compatibility and the selected shade at the shop.
Match a joint to the kitchen floor · Spanish audio
For this jobOTTOSEAL S125 ↗ For a compatible floor joint Presch silicone gun ↗ For laying a bead from a cartridge FUGENFUX ↗ For shaping the fresh bead
Check surface compatibility and the selected shade at the shop.

Before opening the cartridge, try the Presch silicone gun in the tightest corner. Check you can turn your wrist and release pressure at the end of the run.

Common mistakes

Acrylic on the floor edge. Skipping the degrease on PVC. Filling a wide slot without backer rod. A hybrid or silicone that is too stiff below: the floor still wants to move.

Dry-fit the FUGENFUX profiling tool. Choose the edge that meets both sides without scooping out the middle, then tool the bead before a skin forms.

Tools and materials for this job

  • OTTOSEAL A205

    For a dry joint that will be painted. Check movement and paint compatibility.

  • OTTOSEAL S125

    For a compatible floor joint where sealing is allowed. This is the sealant, not a colour chart.

  • Presch silicone gun

    Manual cartridge gun. Check you can release pressure in the last centimetre.

  • FUGENFUX

    Profiling tool. Dry-fit the edge that reaches both sides of the joint.

Exceptions

Solid timber skirting on a stone floor has different chemistry and movement; the principle (wet and elastic below, paintable above) usually still holds. A floor that already humps is a perimeter problem, not a cartridge colour.

More on this

Guides · Floors & skirtings

Where tile meets click vinyl in a doorway →