How to test sealant on microcement

Shop the products for this jobShop all products →
S70Buy S70 ↗PRESCHBuy PRESCH ↗

Identify the topcoat and test the product in an inconspicuous spot. A mineral appearance does not identify the surface finish.

Rogier · Silicrack

Microcement: which silicone, and where it stains
Short answer

I use a neutral stone-type silicone, without migrating plasticisers, matt if the floor is matt. Wait until the sealer has cured. A crack in the render is not filled with a cartridge.

See tools and materials ↓

Buying through a product link may earn us a commission at no extra cost to you.

Why the microcement finish matters

Microcement (the “beton ciré” look) is a mineral render, a little porous, with a protective coat. Ordinary bathroom acetoxy sanitary silicone leaves dark oil halos beside the joint. Plasticisers migrate by capillary action or attack the sealer. You cannot sand that out.

For movement joints — corners, the meeting with the drain — I want a neutral silicone made for natural stone and mineral substrates, without oils that walk. In the wet zone, closed-cell PE backer rod and, often, primer on the flanks: the sealer closes the pore and, without primer, adhesion lets go when it moves (adhesive failure).

Microcement is not natural stone. Consider OTTOSEAL S70 only if the system supplier approves it on that finish and its topcoat; trial it on a finished sample.

When to seal — and when not

Yes when walls and floor are cured and the sealer has had at least about 72 hours — or whatever the applicator of that microcement asked. Then you seal flexible meetings for water.

No if the microcement or the lacquer still smells fresh, or the substrate is not degreased.

Do not fix with silicone a crack in the render. That is movement in the support behind. Smearing paste on a moving coat looks ugly and leaks again.

If the shower corner is already stained or porous from an earlier leak, the mineral sometimes has to be repaired before you reseal.

Before opening the cartridge, try the Presch silicone gun in the tightest corner. Check you can turn your wrist and release pressure at the end of the run.

How I do it

  1. Substrate dry, dust-free. Degrease with a residue-free technical cleaner. No washing-up liquid: acids and degreasers in the soap mark the sealer.
  2. Backer rod in the corner: stops three-sided adhesion and sets the section.
  3. A thin primer on the flanks; respect the flash-off time.
  4. Neutral silicone, no migrating plasticisers. Matt if the floor is matt.
  5. Tool with a neutral finisher and a spatula. No washing-up soap.
Choose grey for microcement · Spanish audio
For this jobPresch silicone gun ↗ For laying a bead from a cartridge FUGENFUX ↗ For shaping the fresh bead
Check surface compatibility and the selected shade at the shop.

At a stainless or plastic drain, primer on that flank as well: otherwise it lets go under standing wet.

Where the joint design specifies backing, size the Backer rod to the measured width and install it without puncturing it. Its job is to control depth.

Common mistakes

Acetoxy “shower” silicone on mineral. Sealing before the 2K or wax has cured. Tooling with floor cleaner. Filling a crack in the coat as if it were a tile joint.

Dry-fit the FUGENFUX profiling tool. Choose the edge that meets both sides without scooping out the middle, then tool the bead before a skin forms.

Tools and materials for this job

  • OTTOSEAL S70

    For compatible natural stone. Test colour and finish on an offcut.

  • Backer rod

    For depth control where specified. Choose the diameter to suit the measured width.

  • Presch silicone gun

    Manual cartridge gun. Check you can release pressure in the last centimetre.

  • FUGENFUX

    Profiling tool. Dry-fit the edge that reaches both sides of the joint.

Exceptions

Microcement already darkened beside an old joint does not “whiten” with a new bead. A wax sealer and a polyurethane sealer do not behave the same; always wait for that coat to cure, not for a tiling clock.

More on this

Guides · Bathroom

Which silicone is suitable for marble and natural stone? →