Neutral or acetoxy silicone: how to choose

Shop the products for this jobShop all products →
S100Buy S100 ↗S110Buy S110 ↗

Choose for compatibility with both surfaces. The smell while curing cannot replace the application chart.

Rogier · Silicrack

Acetoxy or neutral: the vinegar smell is not a fault
Short answer

If it smells of vinegar, it is acetoxy-cure silicone: on glazed tile, enamel and glass it is often the right tool. On marble, granite, bare aluminium, copper, mirrors and many acrylic trays, choose a neutral system.

See tools and materials ↓

Buying through a product link may earn us a commission at no extra cost to you.

What differs during curing

That vinegar sting is not “cheap sealant” by definition. It is acetic acid coming off as the bead cures. In a ventilated bathroom it is a nuisance for a while; on metal and stone it can be a permanent problem.

Neutral silicone (often alkoxy or oxime) barely smells. It cures more slowly and, if the room does not ventilate early on, it can yellow a bit more. It is not “always better”. It is safer when the substrate will not take acid.

In a standard ceramic bathroom I often use OTTOSEAL S100. On stone, sensitive metal or a plastic tray, I switch to neutral: OTTOSEAL S110 or a natural-stone silicone such as S70, depending on the face.

Where the detail calls for sanitary silicone on two compatible surfaces, consider OTTOSEAL S100. Porous stone needs a stone-compatible product.

When acetoxy is fine

Glazed ceramic tile, enamelled bath, glass. Smooth, non-porous faces where the acid has nothing to corrode or stain. Skin forms quickly: tool it without nodding off.

Do not shoot it “just in case” through the whole house. One-cartridge convenience is exactly how kitchen aluminium gets eaten.

For an exposed façade joint, check OTTOSEAL S110 against both surfaces and choose the finished bead colour before applying.

When to go neutral — and when acid is forbidden

Neutral: natural stone, composite, acrylic trays and other plastics, aluminium profiles, copper, unprotected steel, mirrors (the acid attacks the silvering and leaves black edges).

Never acetoxy on marble, granite or other stain-prone stone. Acid and plasticisers walk into the edge and leave a greasy halo you will not wash out. On uncoated metal, corrosion under the bead: a year later the sealant lets go because the substrate is no longer the same.

If one edge is marble or natural stone, trial OTTOSEAL S70 on an offcut and check the tooling agent before touching the visible surface.

Dry-fit the FUGENFUX profiling tool. Choose the edge that meets both sides without scooping out the middle, then tool the bead before a skin forms.

How I choose on site

  1. Identify the substrate for real, not the “sanitary” colour on the cartridge.
  2. Get dust and grease off with a technical cleaner, not kitchen glass spray.
  3. On porous faces, a primer often lengthens the life of a neutral system. It is not the same bottle as the degreaser.
  4. Apply in a continuous bead. Acetoxy wants faster tooling.
  5. Tool with a neutral finisher, not washing-up liquid.

Ventilate if you use acetoxy. Your lungs are not a footnote.

Before opening the cartridge, try the Presch silicone gun in the tightest corner. Check you can turn your wrist and release pressure at the end of the run.

Tools and materials for this job

  • OTTOSEAL S100

    Sanitary silicone for compatible surfaces. Check both edges before opening the cartridge.

  • OTTOSEAL S70

    For compatible natural stone. Test colour and finish on an offcut.

  • OTTOSEAL S110

    Neutral construction silicone. Check both substrates on the data sheet.

  • Presch silicone gun

    Manual cartridge gun. Check you can release pressure in the last centimetre.

  • FUGENFUX

    Profiling tool. Dry-fit the edge that reaches both sides of the joint.

Usual mistakes

Acetoxy sanitary silicone on a stone floor: the famous dark stripe beside the joint. No magic takes it out.

Acetoxy behind a mirror: black marks in the silvering.

Neutral over acetoxy leftovers, or the other way round: silicone does not bond to cured silicone. The old layer has to come out fully. Do not mix chemistries halfway along the same flank.

For an aluminium frame, neutral. The acid oxidises; then you blame “bad glue”.

More on this

Guides · Bathroom

Which sealant should you use in a bathroom? →