How far will one cartridge of sealant go?

Shop the products for this jobShop all products →
PRESCHBuy PRESCH ↗StanleyBuy Stanley ↗

Measure width and depth in several places. A deep joint uses more material than a narrow bead of the same length.

Rogier · Silicrack

How many metres you get from a cartridge
Short answer

Metres ≈ cartridge ml ÷ (width mm × depth mm). A 310 ml tube at 6×6 mm is about 8.6 m before waste. Allow a loss for tooling, check the real fill on the cartridge, and do not pack deep voids with silicone.

See tools and materials ↓

Buying through a product link may earn us a commission at no extra cost to you.

Calculating the volume of the joint

A cartridge is a volume. A joint is a rectangle (more or less) of width times depth. Divide one by the other and you have theoretical metres:

metres ≈ millilitres ÷ (width in mm × depth in mm)

A common 310 ml sanitary cartridge at a 6×6 mm bathroom joint is about 8.6 m on paper. That is geometry, not a brand promise. If you print 4×4 mm you get roughly 19 m; 8×6 mm about 6.5 m; 10×10 mm about 3.1 m; 15×10 mm about 2 m. The numbers fall off a cliff as soon as the joint gets fat.

Some DIY tubes hold less than 310 ml. Read the print. A “cheap” cartridge that is 280–300 ml is simply a shorter stick.

Run a test length with the Presch silicone gun and measure the actual bead. A heavy start wastes material without adding useful depth.

Why the calculator lies

If you smear a thin skin, you “save” silicone and get a weak joint that peels. If you pack the joint properly to both flanks, you use the volume the sum assumed. Tooling then pulls a ribbon of waste onto the spatula. A generous nozzle dumps even more on the tile face. I treat about 10–20 % loss as a working allowance, not a laboratory figure. If the sum says you land exactly on one cartridge, buy a second. Stopping mid-run to change tubes leaves a lump that you will see in raking light — often on the vertical shower corner.

Cut the nozzle to the joint width, not wider. A gaping spout is a waste machine.

When preparing a fresh cartridge, use the Stanley knife as instructed. Cut the nozzle away from your fingers. This cartridge tool is not a scraper for glass, fabric or a shower tray.

Deep gaps are not a silicone well

A joint deeper than about 10 mm should not be filled solid. Closed-cell PE backer rod sets the depth, gives two-sided adhesion, and stops you pouring a cartridge into a cavity. Packing a 20 mm well with silicone wastes money and overloads the joint. Consumption without backer can multiply on a deep meeting; the quality does not.

Cheap silicones extended with solvents can shrink as they cure, so the wet metres you bought are not the cured section you keep. A high-solids sanitary silicone (I use OTTOSEAL S100 on a normal shower) holds its volume better. Still measure the joint, not the marketing.

How I count a bathroom

  1. Measure every shower, bath and basin meeting you will seal — verticals and the floor line.
  2. Measure width. Take depth as similar to width up to about 10 mm; beyond that, limit silicone depth with Backer rod.
  3. Run the formula. Multiply by a waste factor so you are not empty on the last metre.
  4. Plan whole runs from one cartridge where you can.

A compact shower enclosure might be on the order of several metres, not a mystery. A full bathroom renovation is usually more than one tube. A round basin is circumference, not diameter: measure the actual path of the bead.

Hybrid sealant is not “more economical”. Consumption is still the hole you fill. Hybrids can feel stiffer, so people over-apply.

Tools and materials for this job

  • Backer rod

    For depth control where specified. Choose the diameter to suit the measured width.

  • Presch silicone gun

    Manual cartridge gun. Check you can release pressure in the last centimetre.

  • Stanley knife

    For opening the cartridge and trimming the nozzle, not scraping delicate surfaces.

Exceptions

An open joint you can see through is not a 6×6 rectangle; the sum under-reads until you set backer and a real section. Leftover in a sealed nozzle can last a few weeks for a small job; it is not a spare bathroom’s worth of insurance.

More on this

Guides · Prep & joint design

How deep should a sealant joint be? →