Silicone or acrylic: which fits the joint?

Shop the products for this jobShop all products →
A205Buy A205 ↗S100Buy S100 ↗

Decide whether the joint must accept paint, water or movement. Those answers narrow the choice before you open the cartridge.

Rogier · Silicrack

Silicone or acrylic: they are not interchangeable
Short answer

Where there is water and movement you use silicone, and you do not paint it. Where you will paint in the dry, you use acrylic sealant. The other way round, you get pudding in the shower or fish-eyes in the paint.

See tools and materials ↓

Buying through a product link may earn us a commission at no extra cost to you.

Paint, water and movement

Silicone (bathrooms, wet kitchen, glass): sheds water, stays elastic and, if it is decent sanitary grade, carries mould protection. You do not paint it. Shower, WC, sink and junctions that move: this is the material.

Acrylic sealant (living room, bedroom, stair, ceiling, skirting to be painted): cures by water evaporating and goes harder. It is for closing gaps before paint. In the wet shower corner it soaks, softens, moulds and lets go.

If acrylic is already in the shower, take it out. It will not “hold for a bit”.

For a dry interior joint that will be painted, check the expected movement against the data sheet for OTTOSEAL A205. Try the finish with your actual paint.

Where the detail calls for sanitary silicone on two compatible surfaces, consider OTTOSEAL S100. Porous stone needs a stone-compatible product.

Why paint and silicone fight

Silicone has very low surface tension: it throws off water and paint as well. The film pulls into islands, craters, fish-eyes. Acrylic is more porous and paint will key to it.

“Paintable silicones” exist. On site, after a while, the paint often crazes because the bead stays more elastic than the paint film. If you will really paint, use real acrylic (or a hybrid with your eyes open, especially outside).

Before opening the cartridge, try the Presch silicone gun in the tightest corner. Check you can turn your wrist and release pressure at the end of the run.

How to tell which tube it is if the label is gone

Smells of vinegar: acetoxy silicone, no argument.

Rubbed between fingers: greasy and water will not shift it, silicone. Washes off with water, water-based acrylic.

On an old joint: if a fingernail springs back like rubber, silicone; if the dent stays or it is rock-hard, acrylic.

Dry-fit the FUGENFUX profiling tool. Choose the edge that meets both sides without scooping out the middle, then tool the bead before a skin forms.

The usual mistakes

Interior acrylic on a façade or a sill in the first rain, if it has not cured: it washes out. Outside, often hybrid or silicone, not the skirting tube.

Cheap acrylic that shrinks a lot: if you paint too soon, the paint still splits. Wait at least 24 hours on a normal joint; in the cold or on fat joints, longer.

Silicone on a timber floor that still needs varnish: contamination. The varnish will never wet that spot again.

Site order: skirtings and stairs with acrylic before the last paint coat. Sanitary work with silicone after painting, so you do not grease the enamel.

Tools and materials for this job

  • OTTOSEAL A205

    For a dry joint that will be painted. Check movement and paint compatibility.

  • OTTOSEAL S100

    Sanitary silicone for compatible surfaces. Check both edges before opening the cartridge.

  • Presch silicone gun

    Manual cartridge gun. Check you can release pressure in the last centimetre.

  • FUGENFUX

    Profiling tool. Dry-fit the edge that reaches both sides of the joint.

Exceptions

A bathroom corner away from water, to be painted: acrylic. The shower tray, no.

Wide acrylic joints: sometimes two passes, or a low-shrink acrylic. If it always cracks, the gap is too wide, or you painted over the shrink.

More on this

Guides · Prep & joint design

Can you paint silicone sealant? →